Update LCD_Keypad_Shield_with_PH_Meter.ino
This commit is contained in:
vjclearscreen
+472
-251
@@ -31,12 +31,45 @@
|
||||
|
||||
**************************************************************************************/
|
||||
|
||||
/* PIN NRF Mysensor on a arduino Mega :
|
||||
|
||||
modifier fichier libriaire myconfig.h
|
||||
/**********************************
|
||||
* NRF24L01 Driver Defaults
|
||||
***********************************
|
||||
#define RF24_CE_PIN 48
|
||||
#define RF24_CS_PIN 49
|
||||
#define RF24_PA_LEVEL RF24_PA_MAX
|
||||
#define RF24_PA_LEVEL_GW RF24_PA_LOW
|
||||
|
||||
|
||||
48 CE orange
|
||||
49 CSN/CS jaune
|
||||
52 SCK vert
|
||||
51 MOSI bleu
|
||||
50 MISO violet
|
||||
2 IRQ gris
|
||||
|
||||
*/
|
||||
|
||||
#include <LiquidCrystal.h>
|
||||
#include <OneWire.h>
|
||||
#include <DallasTemperature.h>
|
||||
#include <Wire.h>
|
||||
#include <EEPROM.h>
|
||||
// librairie pour My Sensor
|
||||
#include <SPI.h>
|
||||
#include <MySensor.h>
|
||||
|
||||
// configuration my sensor
|
||||
MySensor gw;
|
||||
MyMessage msgPH(0, V_VAR1);
|
||||
MyMessage msgTempROOM(1, V_TEMP);
|
||||
MyMessage msgTempWATER(2, V_TEMP);
|
||||
double lastPhValue = 7;
|
||||
|
||||
LiquidCrystal lcd(8, 9, 4, 5, 6, 7); // select the pins used on the LCD panel
|
||||
#define ONE_WIRE_BUS 2 // DS18B20 connect to Pin 2
|
||||
#define ONE_WIRE_BUS 3 // DS18B20 connect to Pin 2
|
||||
|
||||
OneWire oneWire(ONE_WIRE_BUS);
|
||||
DallasTemperature sensors(&oneWire);
|
||||
@@ -44,7 +77,7 @@ DallasTemperature sensors(&oneWire);
|
||||
#define STX 0xAA // define STX for serial communication
|
||||
#define ETX 0XBB // define ETX for serial communication
|
||||
|
||||
byte RxCmd [4] = {0,0,0,0};
|
||||
byte RxCmd [4] = {0, 0, 0, 0};
|
||||
|
||||
// define some values used by the panel and buttons
|
||||
int lcd_key = -1;
|
||||
@@ -59,16 +92,30 @@ int TempReadings[NumReadings]; // array for store LM35 readings
|
||||
int TempTotal = 0; // LM35 running total
|
||||
int TempAverage = 0; // LM35 average reading
|
||||
double TempValue = 0; // LM35 Temperature Data in Human Reading Format after calculation
|
||||
|
||||
float lastTempROOM = 0;
|
||||
float lastTempWATER = 0;
|
||||
int PhReadings[NumReadings]; // array for store PH readings
|
||||
int PhTotal = 0; // PH running total
|
||||
int PhAverage = 0; // PH average reading
|
||||
|
||||
double Ph7Buffer = 6.86; // For PH7 buffer solution's PH value , 7 or 6.86
|
||||
|
||||
// the current address in the EEPROM (i.e. which byte
|
||||
// we're going to write to next)
|
||||
int addrph4 = 40;
|
||||
int addrph7 = 70;
|
||||
|
||||
double Ph7Buffer = 7.00; // For PH7 buffer solution's PH value , 7 or 6.86
|
||||
double Ph4Buffer = 4.01; // For PH4 buffer solution's PH value , 4 or 4.01
|
||||
|
||||
double Ph7Reading = 528; // PH7 Buffer Solution Reading.
|
||||
double Ph4Reading = 655; // PH4 Buffer Solution Reading.
|
||||
//double Ph7Reading = 528; // PH7 Buffer Solution Reading.
|
||||
//double Ph4Reading = 655; // PH4 Buffer Solution Reading.
|
||||
//double Ph7Reading = 628; // PH7 Buffer Solution Reading.
|
||||
//double Ph4Reading = 732;
|
||||
//double Ph7Reading = EEPROM.read(addrph4); // PH7 Buffer Solution Reading.
|
||||
//double Ph4Reading = EEPROM.read(addrph7);
|
||||
double Ph4Reading = EEreadFloat(addrph4);
|
||||
double Ph7Reading = EEreadFloat(addrph7);
|
||||
int calibrate = 0;
|
||||
|
||||
double PhRatio = 0; // PH Step
|
||||
double PhValue = 0; // Ph Value in Human Reading Format after calculation
|
||||
@@ -80,74 +127,138 @@ double PhValue = 0; // Ph Value in Human Reading Form
|
||||
#define btnSELECT 4
|
||||
#define btnNONE 5
|
||||
|
||||
int read_LCD_buttons(){ // read the buttons
|
||||
adc_key_in = analogRead(0); // read the value from the sensor
|
||||
delay(10); // switch debounce delay. Increase this delay if incorrect switch selections are returned.
|
||||
int k = (analogRead(0) - adc_key_in); // gives the button a slight range to allow for a little contact resistance noise
|
||||
if (5 < abs(k)) return btnNONE; // double checks the keypress. If the two readings are not equal +/-k value after debounce delay, it tries again.
|
||||
//lcd.print(adc_key_in); // read button value and print for calibrate
|
||||
int read_LCD_buttons() { // read the buttons
|
||||
adc_key_in = analogRead(0); // read the value from the sensor
|
||||
delay(10); // switch debounce delay. Increase this delay if incorrect switch selections are returned.
|
||||
int k = (analogRead(0) - adc_key_in); // gives the button a slight range to allow for a little contact resistance noise
|
||||
if (5 < abs(k)) return btnNONE; // double checks the keypress. If the two readings are not equal +/-k value after debounce delay, it tries again.
|
||||
//lcd.print(adc_key_in); // read button value and print for calibrate
|
||||
|
||||
// my buttons when read are centered at these valies: 0, 144, 329, 504, 741
|
||||
// we add approx 50 to those values and check to see if we are close
|
||||
// We make this the 1st option for speed reasons since it will be the most likely result
|
||||
// my buttons when read are centered at these valies: 0, 144, 329, 504, 741
|
||||
// we add approx 50 to those values and check to see if we are close
|
||||
// We make this the 1st option for speed reasons since it will be the most likely result
|
||||
|
||||
if (adc_key_in > 1000) return btnNONE;
|
||||
if (adc_key_in < 50) return btnRIGHT;
|
||||
if (adc_key_in < 150) return btnUP;
|
||||
if (adc_key_in < 350) return btnDOWN;
|
||||
if (adc_key_in < 550) return btnLEFT;
|
||||
if (adc_key_in < 750) return btnSELECT;
|
||||
return btnNONE; // when all others fail, return this.
|
||||
if (adc_key_in > 1000) return btnNONE;
|
||||
if (adc_key_in < 50) return btnRIGHT;
|
||||
if (adc_key_in < 150) return btnUP;
|
||||
if (adc_key_in < 350) return btnDOWN;
|
||||
if (adc_key_in < 550) return btnLEFT;
|
||||
if (adc_key_in < 750) return btnSELECT;
|
||||
return btnNONE; // when all others fail, return this.
|
||||
}
|
||||
|
||||
int reading(){ // Reading LM35 and PH Data
|
||||
// Samplin LM35 and PH Value
|
||||
TempTotal= TempTotal - TempReadings[Index]; // subtract the last reading:
|
||||
PhTotal= PhTotal - PhReadings[Index]; // subtract the last reading:
|
||||
int reading() {
|
||||
double Ph4Reading = EEreadFloat(addrph4);
|
||||
double Ph7Reading = EEreadFloat(addrph7);
|
||||
// Reading LM35 and PH Data
|
||||
// Samplin LM35 and PH Value
|
||||
TempTotal = TempTotal - TempReadings[Index]; // subtract the last reading:
|
||||
PhTotal = PhTotal - PhReadings[Index]; // subtract the last reading:
|
||||
TempReadings[Index] = analogRead(1); // read from the sensor : LM35
|
||||
PhReadings[Index] = analogRead(2); // read from the sensor : PH
|
||||
TempTotal= TempTotal + TempReadings[Index]; // add the reading to the temperature total:
|
||||
PhTotal= PhTotal + PhReadings[Index]; // add the reading to the ph total:
|
||||
TempTotal = TempTotal + TempReadings[Index]; // add the reading to the temperature total:
|
||||
PhTotal = PhTotal + PhReadings[Index]; // add the reading to the ph total:
|
||||
Index = Index + 1; // advance to the next position in the array:
|
||||
|
||||
if (Index >= NumReadings){ // if we're at the end of the array...
|
||||
Index = 0; // ...wrap around to the beginning:
|
||||
TempAverage = TempTotal / NumReadings; // calculate the average:
|
||||
PhAverage = PhTotal / NumReadings; // calculate the average:
|
||||
if (Index >= NumReadings) { // if we're at the end of the array...
|
||||
Index = 0; // ...wrap around to the beginning:
|
||||
TempAverage = TempTotal / NumReadings; // calculate the average:
|
||||
PhAverage = PhTotal / NumReadings; // calculate the average:
|
||||
}
|
||||
TempValue = (double) TempAverage / 3.4 * (5/10.24); // LM35 connect to CA3140 for amplify 3 time
|
||||
TempValue = (double) TempAverage / 3.4 * (5 / 10.24); // LM35 connect to CA3140 for amplify 3 time
|
||||
PhValue = (Ph7Reading - PhAverage) / PhRatio + Ph7Buffer; // Calculate PH
|
||||
|
||||
if (PhValue > 6.5) {
|
||||
digitalWrite(53, HIGH); // turn pompe on
|
||||
}
|
||||
if (PhValue < 6) {
|
||||
digitalWrite(53, LOW); // turn pompe off
|
||||
|
||||
}
|
||||
|
||||
|
||||
if (PhValue > lastPhValue + 0.3) {
|
||||
//Serial.println(PhValue);
|
||||
double PHsend = PhValue;
|
||||
gw.send(msgPH.set(PHsend, 1)); // Send the inverse to gw as tripped should be when no water in soil
|
||||
lastPhValue = PhValue;
|
||||
}
|
||||
if (PhValue < lastPhValue - 0.3) {
|
||||
//Serial.println(PhValue);
|
||||
double PHsend = PhValue;
|
||||
gw.send(msgPH.set(PHsend, 1)); // Send the inverse to gw as tripped should be when no water in soil
|
||||
lastPhValue = PhValue;
|
||||
|
||||
}
|
||||
|
||||
// Only send data if ROOM Temperature has changed and no error
|
||||
if (lastTempROOM < TempValue - 0.5 && TempValue != -127.00 && TempValue != 85.00) {
|
||||
if (TempValue != -127.00 && TempValue != 85.00) {
|
||||
// Send in the new temperature
|
||||
gw.send(msgTempROOM.set(TempValue, 1));
|
||||
// Save new temperatures for next compare
|
||||
lastTempROOM = TempValue;
|
||||
}
|
||||
}
|
||||
// Only send data if ROOM Temperature has changed and no error
|
||||
if (lastTempROOM > TempValue + 0.5 && TempValue != -127.00 && TempValue != 85.00) {
|
||||
if (TempValue != -127.00 && TempValue != 85.00) {
|
||||
// Send in the new temperature
|
||||
gw.send(msgTempROOM.set(TempValue, 1));
|
||||
// Save new temperatures for next compare
|
||||
lastTempROOM = TempValue;
|
||||
}
|
||||
}
|
||||
|
||||
|
||||
|
||||
}
|
||||
|
||||
void setup(){
|
||||
lcd.begin(16, 2); // start LCD library
|
||||
void setup() {
|
||||
|
||||
for (int TempThisReading = 0; TempThisReading < NumReadings; TempThisReading++) // initialize all the LM35 readings to 0:
|
||||
TempReadings[TempThisReading] = 0;
|
||||
// pompe PH down
|
||||
pinMode(53, OUTPUT);
|
||||
// start mysensor
|
||||
gw.begin();
|
||||
|
||||
for (int PhThisReading = 0; PhThisReading < NumReadings; PhThisReading++) // initialize all the Ph readings to 0:
|
||||
PhReadings[PhThisReading] = 0;
|
||||
// Send the sketch version information to the gateway and Controller
|
||||
gw.sendSketchInfo("PH Temp Sensor", "1.0");
|
||||
delay(200);
|
||||
// Register all sensors to gw (they will be created as child devices)
|
||||
gw.present(0, S_TEMP);
|
||||
delay(200);
|
||||
gw.present(1, S_TEMP);
|
||||
delay(200);
|
||||
gw.present(2, S_TEMP);
|
||||
delay(200);
|
||||
|
||||
PhRatio = (Ph4Reading - Ph7Reading) / (Ph7Buffer - Ph4Buffer); // Calculate Ph Ratio
|
||||
lcd.begin(16, 2); // start LCD library
|
||||
|
||||
Serial.begin(9600);
|
||||
while(Serial.available()) Serial.read(); // empty RX buffer
|
||||
Serial.println("Starting");
|
||||
for (int TempThisReading = 0; TempThisReading < NumReadings; TempThisReading++) // initialize all the LM35 readings to 0:
|
||||
TempReadings[TempThisReading] = 0;
|
||||
|
||||
for (int PhThisReading = 0; PhThisReading < NumReadings; PhThisReading++) // initialize all the Ph readings to 0:
|
||||
PhReadings[PhThisReading] = 0;
|
||||
|
||||
PhRatio = (Ph4Reading - Ph7Reading) / (Ph7Buffer - Ph4Buffer); // Calculate Ph Ratio
|
||||
|
||||
Serial.begin(115200);
|
||||
while (Serial.available()) Serial.read(); // empty RX buffer
|
||||
Serial.println("Starting");
|
||||
}
|
||||
|
||||
void loop(){
|
||||
void loop() {
|
||||
|
||||
if (Serial.available()) {
|
||||
delay(2);
|
||||
delay(2);
|
||||
RxCmd[0] = Serial.read();
|
||||
if (RxCmd[0] == STX) {
|
||||
int i =1;
|
||||
while(Serial.available()) {
|
||||
int i = 1;
|
||||
while (Serial.available()) {
|
||||
delay(1);
|
||||
RxCmd[i] = Serial.read();
|
||||
//if (RxCmd[i]>127 || i>7) break; //Communication error
|
||||
if (RxCmd[i]==ETX) {
|
||||
if (RxCmd[i] == ETX) {
|
||||
break; //Read all data
|
||||
}
|
||||
i++;
|
||||
@@ -155,239 +266,349 @@ void loop(){
|
||||
}
|
||||
}
|
||||
|
||||
if ( RxCmd[1] == 1 ){
|
||||
lcd.setCursor(9,1);
|
||||
switch (RxCmd[2]) {
|
||||
case 1:{
|
||||
//Serial.print("Command 1 Received "); // Enquiry Water Temperature (DS18B20)
|
||||
Serial.println(sensors.getTempCByIndex(0),2); // Return DS18B20 Data
|
||||
break;
|
||||
}
|
||||
case 2:{
|
||||
//Serial.print("Command 2 Received "); // Enquiry Room Temperature (LM35)
|
||||
Serial.println(TempValue,2); // Return LM35 Data
|
||||
break;
|
||||
}
|
||||
case 3:{
|
||||
//Serial.print("Command 3 Received "); // Enquiry PH Data
|
||||
Serial.println(PhValue,2); // Return PH Data
|
||||
break;
|
||||
}
|
||||
case 4:{
|
||||
//Serial.println("Command 4 Received "); // Enquiry Water Temp. & Room Temp. & PH
|
||||
Serial.println(sensors.getTempCByIndex(0),2); // Return DS18B20 Data
|
||||
Serial.println(TempValue,2); // Return LM35 Data
|
||||
Serial.println(PhValue,2); // Return PH Data
|
||||
break;
|
||||
if ( RxCmd[1] == 1 ) {
|
||||
lcd.setCursor(9, 1);
|
||||
switch (RxCmd[2]) {
|
||||
case 1: {
|
||||
//Serial.print("Command 1 Received "); // Enquiry Water Temperature (DS18B20)
|
||||
Serial.println(sensors.getTempCByIndex(0), 2); // Return DS18B20 Data
|
||||
break;
|
||||
}
|
||||
case 2: {
|
||||
//Serial.print("Command 2 Received "); // Enquiry Room Temperature (LM35)
|
||||
Serial.println(TempValue, 2); // Return LM35 Data
|
||||
break;
|
||||
}
|
||||
case 3: {
|
||||
//Serial.print("Command 3 Received "); // Enquiry PH Data
|
||||
Serial.println(PhValue, 2); // Return PH Data
|
||||
break;
|
||||
}
|
||||
case 4: {
|
||||
//Serial.println("Command 4 Received "); // Enquiry Water Temp. & Room Temp. & PH
|
||||
Serial.println(sensors.getTempCByIndex(0), 2); // Return DS18B20 Data
|
||||
Serial.println(TempValue, 2); // Return LM35 Data
|
||||
Serial.println(PhValue, 2); // Return PH Data
|
||||
break;
|
||||
}
|
||||
}
|
||||
}
|
||||
}
|
||||
|
||||
for (int i = 0 ; i < 5 ; i++) {
|
||||
RxCmd[i] = 0;
|
||||
}
|
||||
|
||||
if (CurrentMode == 0) // Nomral Display Mode
|
||||
{
|
||||
reading(); // Reading LM35 and PH Data for display
|
||||
lcd.setCursor(13,0);
|
||||
lcd.print("PH ");
|
||||
lcd.setCursor(0,0); // set the LCD cursor position
|
||||
lcd.print("Room");
|
||||
lcd.setCursor(0,1);
|
||||
lcd.print("Water");
|
||||
lcd.setCursor(6,0);
|
||||
lcd.print(TempValue); // display room temperature value (LM35)
|
||||
delay(1); // delay in between reads for stability
|
||||
if (CurrentMode == 0) // Nomral Display Mode
|
||||
{
|
||||
reading(); // Reading LM35 and PH Data for display
|
||||
lcd.setCursor(13, 0);
|
||||
lcd.print("PH ");
|
||||
lcd.setCursor(0, 0); // set the LCD cursor position
|
||||
lcd.print("Room");
|
||||
lcd.setCursor(0, 1);
|
||||
lcd.print("Water");
|
||||
lcd.setCursor(6, 0);
|
||||
lcd.print(TempValue); // display room temperature value (LM35)
|
||||
delay(1); // delay in between reads for stability
|
||||
|
||||
// Display 18B20 Temperature
|
||||
lcd.setCursor(6,1); // move cursor to second line "1" and 6 spaces over
|
||||
sensors.requestTemperatures(); // Read DS18B20 data
|
||||
lcd.print(sensors.getTempCByIndex(0)); // Display DS18B20 Data
|
||||
// Display 18B20 Temperature
|
||||
lcd.setCursor(6, 1); // move cursor to second line "1" and 6 spaces over
|
||||
sensors.requestTemperatures(); // Read DS18B20 data
|
||||
lcd.print(sensors.getTempCByIndex(0)); // Display DS18B20 Data
|
||||
int TempWATER = sensors.getTempCByIndex(0);
|
||||
// Only send data if WATER temperature has changed and no error
|
||||
if (lastTempWATER < TempWATER - 0.5 && TempWATER != -127.00 && TempWATER != 85.00) {
|
||||
if (TempWATER != -127.00 && TempWATER != 85.00) {
|
||||
// Send in the new temperature
|
||||
gw.send(msgTempWATER.set(TempWATER, 1));
|
||||
// Save new temperatures for next compare
|
||||
lastTempWATER = TempWATER;
|
||||
}
|
||||
}
|
||||
// Only send data if WATER temperature has changed and no error
|
||||
if (lastTempWATER > TempWATER + 0.5 && TempWATER != -127.00 && TempWATER != 85.00) {
|
||||
if (TempWATER != -127.00 && TempWATER != 85.00) {
|
||||
// Send in the new temperature
|
||||
gw.send(msgTempWATER.set(TempWATER, 1));
|
||||
// Save new temperatures for next compare
|
||||
lastTempWATER = TempWATER;
|
||||
}
|
||||
}
|
||||
|
||||
// Display PH Data
|
||||
lcd.setCursor(13,0);
|
||||
lcd.print("PH");
|
||||
lcd.setCursor(12,1);
|
||||
lcd.print(PhValue); // display PH value
|
||||
delay(1); // delay in between reads for stability
|
||||
// Display PH Data
|
||||
lcd.setCursor(13, 0);
|
||||
lcd.print("PH");
|
||||
lcd.setCursor(12, 1);
|
||||
lcd.print(PhValue); // display PH value
|
||||
delay(1); // delay in between reads for stability
|
||||
|
||||
}
|
||||
}
|
||||
|
||||
if (CurrentMode == 1){
|
||||
reading();
|
||||
lcd.setCursor(0,0);
|
||||
lcd.print("LM35 R");
|
||||
lcd.setCursor(10,0);
|
||||
lcd.print("T");
|
||||
lcd.setCursor(0,1);
|
||||
lcd.print("PH R");
|
||||
lcd.setCursor(10,1);
|
||||
lcd.print("P");
|
||||
if (CurrentMode == 1) {
|
||||
reading();
|
||||
lcd.setCursor(0, 0);
|
||||
lcd.print("LM35 R");
|
||||
lcd.setCursor(10, 0);
|
||||
lcd.print("T");
|
||||
lcd.setCursor(0, 1);
|
||||
lcd.print("PH R");
|
||||
lcd.setCursor(10, 1);
|
||||
lcd.print("P");
|
||||
|
||||
lcd.setCursor(6,0);
|
||||
lcd.print(TempAverage);
|
||||
lcd.setCursor(12,0);
|
||||
lcd.print(TempValue);
|
||||
lcd.setCursor(6, 0);
|
||||
lcd.print(TempAverage);
|
||||
lcd.setCursor(12, 0);
|
||||
lcd.print(TempValue);
|
||||
|
||||
lcd.setCursor(6,1);
|
||||
lcd.print(PhAverage);
|
||||
lcd.setCursor(11,1);
|
||||
lcd.print(PhValue);
|
||||
}
|
||||
lcd.setCursor(6, 1);
|
||||
lcd.print(PhAverage);
|
||||
lcd.setCursor(11, 1);
|
||||
lcd.print(PhValue);
|
||||
}
|
||||
|
||||
if (CurrentMode == 2){
|
||||
reading();
|
||||
double PhVoltage;
|
||||
PhVoltage = (double)PhAverage * (5/10.24);
|
||||
if (CurrentMode == 2) {
|
||||
reading();
|
||||
double PhVoltage;
|
||||
PhVoltage = (double)PhAverage * (5 / 10.24);
|
||||
|
||||
lcd.setCursor(0,0);
|
||||
lcd.print("R:");
|
||||
lcd.setCursor(3,0);
|
||||
lcd.print(PhAverage);
|
||||
lcd.setCursor(0, 0);
|
||||
lcd.print("R:");
|
||||
lcd.setCursor(3, 0);
|
||||
lcd.print(PhAverage);
|
||||
|
||||
|
||||
lcd.setCursor(7,0);
|
||||
lcd.print("Ratio:");
|
||||
lcd.setCursor(13,0);
|
||||
lcd.print(PhRatio);
|
||||
lcd.setCursor(7, 0);
|
||||
lcd.print("Ratio:");
|
||||
lcd.setCursor(13, 0);
|
||||
lcd.print(PhRatio);
|
||||
|
||||
lcd.setCursor(0,1);
|
||||
lcd.print("PH:");
|
||||
lcd.setCursor(3,1);
|
||||
lcd.print(PhValue);
|
||||
}
|
||||
lcd.setCursor(0, 1);
|
||||
lcd.print("PH:");
|
||||
lcd.setCursor(3, 1);
|
||||
lcd.print(PhValue);
|
||||
}
|
||||
|
||||
if (CurrentMode == 3){ // Calibration Mode Selection Page
|
||||
lcd.setCursor(0,0);
|
||||
lcd.print("PH4 Cal ");
|
||||
lcd.setCursor(0,1);
|
||||
lcd.print("PH7 Cal ");
|
||||
if (CalSelect == 0) {
|
||||
lcd.setCursor(8,0);
|
||||
if (CurrentMode == 3) { // Calibration Mode Selection Page
|
||||
lcd.setCursor(0, 0);
|
||||
lcd.print("PH4 Cal ");
|
||||
lcd.setCursor(0, 1);
|
||||
lcd.print("PH7 Cal ");
|
||||
if (CalSelect == 0) {
|
||||
lcd.setCursor(8, 0);
|
||||
lcd.print(">>");
|
||||
}
|
||||
if (CalSelect == 1) {
|
||||
lcd.setCursor(8,1);
|
||||
}
|
||||
if (CalSelect == 1) {
|
||||
lcd.setCursor(8, 1);
|
||||
lcd.print(">>");
|
||||
}
|
||||
}
|
||||
}
|
||||
}
|
||||
|
||||
if (CurrentMode == 4){ // PH4 Calibration Mode
|
||||
reading();
|
||||
lcd.setCursor(0,0);
|
||||
lcd.print("PH4 Cal. Mode");
|
||||
lcd.setCursor(0,1);
|
||||
lcd.print("C:");
|
||||
lcd.setCursor(2,1);
|
||||
lcd.print(Ph4Reading);
|
||||
lcd.setCursor(9,1);
|
||||
lcd.print("R:");
|
||||
lcd.setCursor(11,1);
|
||||
lcd.print(PhAverage);
|
||||
}
|
||||
if (CurrentMode == 4) { // PH4 Calibration Mode
|
||||
|
||||
if (CurrentMode == 5){ // PH7 Calibration Mode
|
||||
reading();
|
||||
lcd.setCursor(0,0);
|
||||
lcd.print("PH7 Cal. Mode");
|
||||
lcd.setCursor(0,1);
|
||||
lcd.print("C:");
|
||||
lcd.setCursor(2,1);
|
||||
lcd.print(Ph7Reading);
|
||||
lcd.setCursor(9,1);
|
||||
lcd.print("R:");
|
||||
lcd.setCursor(11,1);
|
||||
lcd.print(PhAverage);
|
||||
}
|
||||
if (calibrate >= 3) {
|
||||
reading();
|
||||
lcd.setCursor(0, 0);
|
||||
lcd.print("PH4 Calibrate");
|
||||
lcd.setCursor(0, 1);
|
||||
lcd.print("C:");
|
||||
lcd.setCursor(2, 1);
|
||||
lcd.print(Ph4Reading);
|
||||
lcd.setCursor(9, 1);
|
||||
lcd.print("R:");
|
||||
lcd.setCursor(11, 1);
|
||||
lcd.print(PhAverage);
|
||||
delay(2000);
|
||||
reading();
|
||||
double Ph4Reading = PhAverage;
|
||||
lcd.setCursor(0, 0);
|
||||
lcd.print("PH4 Saving ");
|
||||
lcd.setCursor(0, 1);
|
||||
lcd.print("C:");
|
||||
lcd.setCursor(2, 1);
|
||||
lcd.print(Ph4Reading);
|
||||
lcd.setCursor(9, 1);
|
||||
lcd.print("R:");
|
||||
lcd.setCursor(11, 1);
|
||||
lcd.print(PhAverage);
|
||||
//EEPROM.write(addrph4, PhAverage);
|
||||
EEwriteFloat(addrph4, PhAverage);
|
||||
calibrate = 0;
|
||||
delay(2000);
|
||||
}
|
||||
|
||||
if (calibrate < 3) {
|
||||
reading();
|
||||
lcd.setCursor(0, 0);
|
||||
lcd.print("PH4 loded ");
|
||||
lcd.setCursor(0, 1);
|
||||
lcd.print("C:");
|
||||
lcd.setCursor(2, 1);
|
||||
lcd.print(Ph4Reading);
|
||||
lcd.setCursor(9, 1);
|
||||
lcd.print("R:");
|
||||
lcd.setCursor(11, 1);
|
||||
lcd.print(PhAverage);
|
||||
}
|
||||
|
||||
}
|
||||
|
||||
if (CurrentMode == 5) { // PH7 Calibration Mode
|
||||
|
||||
if (calibrate >= 3) {
|
||||
reading();
|
||||
lcd.setCursor(0, 0);
|
||||
lcd.print("PH7 Calibrate");
|
||||
lcd.setCursor(0, 1);
|
||||
lcd.print("C:");
|
||||
lcd.setCursor(2, 1);
|
||||
lcd.print(Ph7Reading);
|
||||
lcd.setCursor(9, 1);
|
||||
lcd.print("R:");
|
||||
lcd.setCursor(11, 1);
|
||||
lcd.print(PhAverage);
|
||||
delay(2000);
|
||||
reading();
|
||||
double Ph7Reading = PhAverage;
|
||||
lcd.setCursor(0, 0);
|
||||
lcd.print("PH7 Saving ");
|
||||
lcd.setCursor(0, 1);
|
||||
lcd.print("C:");
|
||||
lcd.setCursor(2, 1);
|
||||
lcd.print(Ph7Reading);
|
||||
lcd.setCursor(9, 1);
|
||||
lcd.print("R:");
|
||||
lcd.setCursor(11, 1);
|
||||
lcd.print(PhAverage);
|
||||
//EEPROM.write(addrph7, PhAverage);
|
||||
EEwriteFloat(addrph7, PhAverage);
|
||||
//double Ph7Reading = PhAverage;
|
||||
calibrate = 0;
|
||||
delay(2000);
|
||||
}
|
||||
|
||||
if (calibrate < 3) {
|
||||
reading();
|
||||
lcd.setCursor(0, 0);
|
||||
lcd.print("PH7 loaded ");
|
||||
lcd.setCursor(0, 1);
|
||||
lcd.print("C:");
|
||||
lcd.setCursor(2, 1);
|
||||
lcd.print(Ph7Reading);
|
||||
lcd.setCursor(9, 1);
|
||||
lcd.print("R:");
|
||||
lcd.setCursor(11, 1);
|
||||
lcd.print(PhAverage);
|
||||
}
|
||||
}
|
||||
|
||||
|
||||
lcd.setCursor(0,1); // move to the begining of the second line
|
||||
adc_key_prev = lcd_key ; // Looking for changes
|
||||
lcd.setCursor(0, 1); // move to the begining of the second line
|
||||
adc_key_prev = lcd_key ; // Looking for changes
|
||||
|
||||
lcd_key = read_LCD_buttons(); // read the buttons
|
||||
lcd_key = read_LCD_buttons(); // read the buttons
|
||||
|
||||
if (adc_key_prev != lcd_key)
|
||||
{
|
||||
//Serial.println("Key Press Change Detected");
|
||||
switch (lcd_key){ // depending on which button was pushed, we perform an action
|
||||
case btnRIGHT:{ // push button "RIGHT" and show the word on the screen
|
||||
//lcd.print("RIGHT");
|
||||
if ( CurrentMode == 0 ){
|
||||
lcd.clear();
|
||||
CurrentMode = 2;
|
||||
}
|
||||
if ( CurrentMode == 3){
|
||||
lcd.clear();
|
||||
if ( CalSelect == 0 ){
|
||||
CurrentMode = 4;
|
||||
}
|
||||
if ( CalSelect == 1){
|
||||
CurrentMode = 5;
|
||||
}
|
||||
//Serial.println("Key Press Change Detected");
|
||||
switch (lcd_key) { // depending on which button was pushed, we perform an action
|
||||
case btnRIGHT: { // push button "RIGHT" and show the word on the screen
|
||||
//lcd.print("RIGHT");
|
||||
|
||||
calibrate ++;
|
||||
|
||||
|
||||
if ( CurrentMode == 0 ) {
|
||||
lcd.clear();
|
||||
CurrentMode = 2;
|
||||
}
|
||||
if ( CurrentMode == 3) {
|
||||
lcd.clear();
|
||||
if ( CalSelect == 0 ) {
|
||||
CurrentMode = 4;
|
||||
}
|
||||
if ( CalSelect == 1) {
|
||||
CurrentMode = 5;
|
||||
}
|
||||
}
|
||||
break;
|
||||
}
|
||||
case btnLEFT: {
|
||||
//lcd.print("LEFT "); // push button "LEFT" and show the word on the screen
|
||||
if ( CurrentMode == 2 ) {
|
||||
lcd.clear();
|
||||
CurrentMode = 0;
|
||||
}
|
||||
if ( CurrentMode == 3 ) {
|
||||
lcd.clear();
|
||||
CurrentMode = 0;
|
||||
}
|
||||
if ( CurrentMode == 4 || CurrentMode == 5 ) {
|
||||
lcd.clear();
|
||||
CurrentMode = 3;
|
||||
}
|
||||
|
||||
break;
|
||||
}
|
||||
case btnUP: {
|
||||
//lcd.print("UP "); // push button "UP" and show the word on the screen
|
||||
if ( CurrentMode == 0 ) {
|
||||
lcd.clear();
|
||||
CurrentMode = 1;
|
||||
}
|
||||
if ( CurrentMode == 3 ) {
|
||||
lcd.clear();
|
||||
CalSelect = 0;
|
||||
}
|
||||
break;
|
||||
}
|
||||
case btnDOWN: {
|
||||
//lcd.print("DOWN "); // push button "DOWN" and show the word on the screen
|
||||
if ( CurrentMode == 1) {
|
||||
lcd.clear();
|
||||
CurrentMode = 0;
|
||||
}
|
||||
if ( CurrentMode == 3 ) {
|
||||
lcd.clear();
|
||||
CalSelect = 1;
|
||||
}
|
||||
break;
|
||||
}
|
||||
case btnSELECT: {
|
||||
|
||||
//lcd.print("SEL. "); // push button "SELECT" and show the word on the screen
|
||||
if ( CurrentMode == 0 ) {
|
||||
lcd.clear();
|
||||
CurrentMode = 3;
|
||||
break;
|
||||
}
|
||||
case btnLEFT:{
|
||||
//lcd.print("LEFT "); // push button "LEFT" and show the word on the screen
|
||||
if ( CurrentMode == 2 ){
|
||||
lcd.clear();
|
||||
CurrentMode = 0;
|
||||
}
|
||||
if ( CurrentMode == 3 ){
|
||||
lcd.clear();
|
||||
CurrentMode = 0;
|
||||
}
|
||||
if ( CurrentMode == 4 || CurrentMode == 5 ){
|
||||
lcd.clear();
|
||||
CurrentMode = 3;
|
||||
}
|
||||
}
|
||||
if ( CurrentMode == 3 ) {
|
||||
lcd.clear();
|
||||
CurrentMode = 0;
|
||||
break;
|
||||
}
|
||||
break;
|
||||
|
||||
break;
|
||||
}
|
||||
case btnUP:{
|
||||
//lcd.print("UP "); // push button "UP" and show the word on the screen
|
||||
if ( CurrentMode == 0 ){
|
||||
lcd.clear();
|
||||
CurrentMode = 1;
|
||||
}
|
||||
if ( CurrentMode == 3 ){
|
||||
lcd.clear();
|
||||
CalSelect = 0;
|
||||
}
|
||||
break;
|
||||
}
|
||||
case btnDOWN:{
|
||||
//lcd.print("DOWN "); // push button "DOWN" and show the word on the screen
|
||||
if ( CurrentMode == 1){
|
||||
lcd.clear();
|
||||
CurrentMode = 0;
|
||||
}
|
||||
if ( CurrentMode == 3 ){
|
||||
lcd.clear();
|
||||
CalSelect = 1;
|
||||
}
|
||||
break;
|
||||
}
|
||||
case btnSELECT:{
|
||||
//lcd.print("SEL. "); // push button "SELECT" and show the word on the screen
|
||||
if ( CurrentMode == 0 ){
|
||||
lcd.clear();
|
||||
CurrentMode = 3;
|
||||
break;
|
||||
}
|
||||
if ( CurrentMode == 3 ){
|
||||
lcd.clear();
|
||||
CurrentMode = 0;
|
||||
break;
|
||||
}
|
||||
break;
|
||||
|
||||
}
|
||||
case btnNONE:{
|
||||
//lcd.print("NONE "); // No action will show "None" on the screen
|
||||
break;
|
||||
}
|
||||
}
|
||||
}
|
||||
}
|
||||
case btnNONE: {
|
||||
//lcd.print("NONE "); // No action will show "None" on the screen
|
||||
break;
|
||||
}
|
||||
}
|
||||
}
|
||||
}
|
||||
|
||||
void EEwriteFloat(int addr, float f) {
|
||||
unsigned char *buf = (unsigned char*)(&f);
|
||||
for ( int i = 0 ; i < sizeof(f) ; i++ ) {
|
||||
EEPROM.write(addr + i, buf[i]);
|
||||
}
|
||||
}
|
||||
|
||||
float EEreadFloat(int addr) {
|
||||
float f;
|
||||
unsigned char *buf = (unsigned char*)(&f);
|
||||
for ( int i = 0 ; i < sizeof(f) ; i++ ) {
|
||||
buf[i] = EEPROM.read(addr + i);
|
||||
}
|
||||
return f;
|
||||
}
|
||||
|
||||
Reference in New Issue
Block a user